Woodshop Life Podcast

This Episodes Questions:

Brian's Questions:

My neighbor gave me a beautiful maple root ball that is approximately 3' in diameter about 6 months ago. I am currently letting it dry for another 12 to 24 months. I'm thinking of eventually rough cutting it with a large reciprocating saw. The wood will be used for small boxes or knife handles. Am I crazy? Do you have any advice on dry times and using root wood? George

Guy, I am making a bow front dresser and plan to use Blum Blumotion undermount slides for the drawers. However, I’m not sure how I should attach the front of the slide to the bottom of the draw, since the draw front will be curved. Any suggestions would be greatly appreciated. Also, the draws will be inset, but since the blumotion has a fair amount of flexibility (up/down and left/right)  I am thinking aligning the draw fronts should be doable. But do you have any suggestions to make it as simple as possible? Finally I see Rockler has a “JIG IT” under mount drilling guide. Do you use this jig and do you recommend it? Thanks so much!!! Mike

Guy's Questions:

I live in Fishers, IN and am new to woodworking and was wondering how to find good places for hardwoods? It’s been pretty tough to find anything local without driving a decent distance to a mill on the west side of town. Chayse Bell

I’m preparing to build a set of kitchen cupboards from white oak.  The style will be Mission, with some Frank Lloyd Wright Prairies Style touches.  I have several questions. How much planer snipe is too much?  I have a Dewalt 13” model 735 benchtop planer.  If I take a short board—say, two feet—and run it through once taking a 1/16 cut, I get 8/1000ths snipe.  Is this to be expected?  …or should I look at getting my planer serviced or maybe trading up.  (The Laguna Tools PX16 planer looks amazing, but six times the money.) Darrin

Huy's Questions:

Thank you all for what you do. Like so many other woodworkers, I have accumulated quite a bit of wood through my own purchases and also from inheriting my fathers wood collection after he passed away. I would like to move it out of my two car garage workshop to free up space, and am considering building some sort of dry storage box to store it under a deck in my backyard. (I don’t have room for a large lumber shed). Thinking roughly 14 foot by 4 foot by 4 foot.  This box would obviously be exposed to the weather as the deck is not sealed. What are your thoughts on this?  And if you were to build this box, would you seal it relatively airtight or would you simply stack the lumber off the ground and put a piece of tin or something over the top to allow airflow. In the second example, I worry about snow, rain and bugs getting access to the lumber. Thanks in advance for your response. Eric in Lincoln Nebraska

Hey gentleman, first of all, thank you for the amazing podcast and the fluff-free format. I’ve been a hobbyist woodworker for about 6 years and I’m at the point where I’m considering turning my hobby into a side job of sorts. My question is: in your opinion, what separates an amateur woodworker from a professional woodworker? Are there certain skills, techniques, or projects you learned that really elevated your confidence or status in the craft? Thanks again, and keep up the awesome content! Adrien from Toronto (Canada)

This Episodes Questions:

Brian's Questions:

I’m preparing to build a set of kitchen cupboards from white oak.  The style will be Mission, with some Frank Lloyd Wright Prairies Style touches.  I have several questions.  I have a question about milling lumber.  There seems to be a trade-off: keep the boards long and you need to joint more off to get a flat face, hence the risk of falling below your desired thickness.  But cut the boards to length first and you have to allow for more cut-offs on the ends to remove planer snipe.  How should I think about this?  In general, do the three of you cut longer boards to length for parts first and then plane and joint?  Or do you joint and plane the boards whole (mine are 6’ to 8’) and take the perhaps larger losses to thickness but avoid multiple areas of planer snipe?   I know that much depends on the boards, but I'd be interested in your general approaches.  Darrin    Hey guys I absolutely love the podcast, amd have already learned a lot. I recently have decided to do this for more than a hobby. I have been doing small or easier projects like cutting boards and tongue and groove ceilings. I have been wanting to start building entry level tables and furniture but keep psyching myself out of it. How did you guys build up the confidence to move on to more advanced projects? And did you guys get discouraged or frustrated at the beginning?

Thank you David Caraway

Guy's Questions:

Thank you all for such a great show!  I'm an amateur woodworker working out of a 550 square foot two-car attached garage.  We keep two cars in the garage, so all my equipment is on mobile bases. My question has to do with shop climate control.  I live in southern Indiana, with hot muggy summers and cool-to-cold winters.  The garage is insulated, including the door, and sits under a conditioned bonus room, but the garage itself is not heated or cooled.  Although it never freezes, for a few of the coldest winter weeks, it will be in upper 30s.  Mostly it's at least 45 degrees. I'm contemplating installing a 1 ton/12,000BTU mini-split for heating and cooling, DIYing installing it for less than $1000.  I'm trying to decide if it's worth it, basically for the few hottest and coldest weeks.  I can also migrate easily to my unfinished basement in the coldest weeks for glue-ups and finishing.  I wouldn't want to run the mini-split all the time, and often I am only out in the shop for short bursts, so pre-heating or pre-cooling seems wasteful.  $1000, plus the energy to run the mini-split, could buy plenty of other woodworking equipment and supplies.  If this were your shop, what would you do? Thanks, Kyle Kramer

Always a pleasure listening to your podcast.  Thank you for your knowledge and insight. I am planning to rip the carpet off my Stairs treads and somehow get a relative match to my wood flooring either upstairs and downstairs.  Assuming the exact color isnt important in my question. The treads are likely just pine but I haven't pulled the carpet yet to find out.  My thought was to veneer the treads.  Then I would most likely us a transtint dye to reach the color and finish off with shellac washout and water based poly for durable finish.  Is this a good approach or destined for failure? Thanks for your time. Josh

Huy's Questions:

Thanks for the great podcast. I have learned a lot from all the great content you put out. I really appreciate your advice and perspective. I have a couple questions I was hoping you could answer. My second question is about compositing saw dust. My wife likes to garden and keep a compost pile. We use saw dust and wood shaving to balance the moisture of the compost pile. I occasionally use MDF and plywood  and I am wondering if all the bad stuff in those materials are bad to use in the compost. I guess I'm pretty sure they are not good. I've heard that most of those chemicals breakdown form the heat of the compost but I am skeptical of that. I use an oneida dust separator. Do you think it is worth trying to partition two dust bins, one for raw wood and one for everything else? Do you think a blast gate under the separator would accomplish that or would it mess with the air flow of the separator? Thanks. Keep up the great work. Jon Moch

A lot of people talk about spraying water on wood when changing sanding grits, to raise the loose fibres and get a smoother finish. I have taken to spraying isopropyl alcohol (I think you would call it rubbing alcohol) between grits. I can spray it quite heavily and have it evaporate within a minute so I can continue sanding without having to wait. I doubt I'm the first person in the history of woodworking to think of this (I'm no rocket scientist, Huy), but I never hear of anyone else doing this. That makes me think there may be a good reason to not do this. So what do you blokes reckon? Is there a reason why I shouldn't be doing this, apart from water being free and alcohol being expensive? FYI, I usually work in recycled jarrah (an ultra hard Western Australian wood) and finish with Tung oil when using the alcohol Thanks fellas, love your work! Jim

This Episodes Questions:

Brian's Questions:

I know planing before face jointing is sacraledge but I was recently visiting with an older experienced wood worker who noted he never face joints. Planes both sides then edge joints and it’s fine.

Thoughts? Thinking if you want it dead flat perfect or board is not great to start with jointing certainly makes sense. But anybody just plane it? Perhaps starting with a decent board it would work for most applications?

My 20” planer is a breeze to put wood through, the jointer is great but takes more effort/time if it’s not needed would be a nice step to drop.

Curious on your thoughts, Matt Wendig

I’m preparing to build a set of kitchen cupboards from white oak.  The style will be Mission, with some Frank Lloyd Wright Prairies Style touches.  I have several questions.  I need to cut up a lot of 3/4" plywood.  I have a good track saw and a cabinet tablesaw with side and outfeed tables.  When watching videos of some people constructing kitchen cabinets, I’m surprised that they cut the sheet goods with the track saw but then cut them again, to final size, on the table saw.  I imagined myself using the track saw only—to do very precise cuts to final size and not cutting the panels twice.  What is your process?  Any advice on maximizing my chances of getting near-perfect panels with the track saw only and avoiding the two-cuts process? Darrin    Guy's Questions:    Hey guys, love the podcast. I’m making a screen door for the porch out of cedar that is 1.5” thick, 36” x 84” with 5.5” wide stiles and rails (top, middle and bottom). I have a festool DF500, if I used 10 x 50 dominoes for the joinery would that be strong enough or should I use traditional mortise and tenons?

I’ve read that cedar is pretty dimensionally stable. I was thinking about just staining or oiling the door (I don’t want it to turn gray) but does it need an actual topcoat to help keep it from warping? Just don’t want to use a finish that is going to flake off and I will have to sand and refinish every year or so. If it needs a topcoat could you recommend a finish?

Thanks, Scott in Birmingham.

Throughly enjoy the pod cast. I am almost up to date on all past episodes and they hve been quite informative. Little back story on my question. Had a client contact me about repairing a dinning table they had built for their home. For clarity I didn’t build the table. The top is a solid wood glue up with breadboards on the ends. On one end of the top the breadboard sticks out about 1/16” past the rest of the top. On the other end 2 boards have a split between the glue line  that stretches roughly 2 feet along their length. I’m sure it is from the wood contracting. Any pointers on how to repair the issue?  I’m 99.9% sure the table top is made from southern yellow pine. It is stained with a top coat of poly acrylic. Robert

Huy's Questions:

Hello guys,

I love the podcast and have learned a ton from you. Keep up the great work and thank you for your time. 

I have a question on how you store your tools that require precision/calibration. Specifically, I have an Incra 5000 cross cut sled. When not in use, I store it standing on its side on the shop floor. Is there a better / more correct way? Similar question goes for any other shop made sled / jig that you expect to use over and over again. How do you store it?

Max Greddie Woodworks

It was mentioned that one of you repalced the wheels on his band saw, do to it wearing out and it was a pain. I have bought a used 14 inch delta bandsaw, and I have no idea how to know if parts are worn out beside the obvious part being the blade. So how can I figure out parts are worn out, sources to shop for replacements ( no home depo in Okinawa) tips and or youtube videos on how to do these maintainance tasks? Oh and what you do to increase the function of a band saw, like would you buy a bow system fence for it?

Many thanks, Paul Mitchell Oki Mitch Crafts

This Episodes Questions:

Brians Questions:

Hi Guys love your podcast.  I have a quick question regarding table saw blades.  Can you give me a recommendation on a good quality 10" table saw blade that I can get re-sharpened when needed.  I keep blowing through blades and I'm tired of buying new ones.  Also, do you send the blades back to get re-sharpened or take them to your nearest local blade sharpening place thanks in advance Dave

I’m making an ash table top (never used ash before) and had a few questions. How should I edge join the boards for glue up (domino or biscuits), what’s the best finish for ash when used as a desk to avoid feeling the grain on ash. I don’t have a sprayer but could be a good excuse to get one.  What edge profiles do you guys like to use for tables and/or desk that get lots of use and also look good? Chayse

Guy's Questions:

My latest project is an Arts & Crafts sideboard made in quartersawn white oak. I'm at the point in the project where I need to start thinking about how to finish the piece.  Its my first time working with this wood and I'm considering fuming the piece with ammonia as I've read that this process will really make the grain rays stand out.  People seem pretty divided on whether its worth the time and risk of working with harmful chemicals and I wanted to get your collective thoughts and experience.  Have you used an ammonia fuming process? Do you think its worth it?  Any tips or tricks to share?  I'm in the northeast so the current low temps add some complexity as I've learned that colder temperatures slow down the process. Regards, Adam

I'm working on a veneered box. Normally you'd glue a similarly oriented veneer on the back surface to prevent warping. For the veneer, I'm planning on cross cutting small strips and then gluing them together, roughly like how inlays are made. I'll then be cutting thin slices from the resulting laminated assembly. I'll be using the thin slices as the veneer, like a mosaic or a quilt. The grain of these thin slices will run in different directions. Do I still need a backing? If so, in which direction should the backing grain run? Lauris

Huy's Questions:

The topic of wood movement comes up pretty regularly on this show. When it does, however, it is typically related to questions on how to account for it in regards to a specific project or joinery method. Meanwhile, I'm sitting here wondering what wood movement actually is. I understand that humidity and temperature cause wood to expand or contract, but that's about where my understanding ends. Why is it important to account for wood movement? What happens if you don't? What is this business I've heard mentioned about projects exploding? On a related note, often when questions about mitigating wood movement come up the answers to those questions are something along the lines of "If you use __________ (type of joinery, layout, etc) you shouldn't have to worry about wood movement." As someone still very new to the principles of woodworking, the question I always have is: why? Why will using such and such method or assembling your project in this or that manner mitigate wood movement? Zach

Hey guys. Love your podcast and appreciate the help you’ve given me over the years with your knowledge and experience in the craft. I have an entryway table I’m building out of walnut and cocobolo. The top will consist of a glue up of the two woods. What glue should I use for the glue up since cocobolo is very oily? And what sort of finish would you recommend for this application? Thanks again and take care!  Ryan of Mountain Custom Woodworks